BS EN 1106:2022

$189.07

Manually operated taps for gas burning appliances

Published By	Publication Date	Number of Pages
BSI	2022	46

Guaranteed Safe Checkout

Categories: 23.060.40 - Pressure regulators, BSI

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

EN 13611:2019, Clause 1 applies with the following modification and addition: Modification: The 1st paragraph of EN 13611:2019, Clause 1 is replaced by: This document specifies the safety, design, construction, and performance requirements and testing for manually operated taps and presetting taps for burners and appliances burning one or more gaseous fuels, hereafter referred to as “taps”. This document is applicable to taps with declared maximum inlet pressures up to and including 50 kPa and of nominal connection sizes up to and including DN 50 for use with one or more fuel gases. Addition: This document is not applicable to: a) manual operated shut-off valves conforming to EN 331:2015; b) controls which use auxiliary energy (e.g. electrical energy supplied externally). The 4th paragraph of EN 13611:2019, Clause 1 is removed.

PDF Catalog

PDF Pages	PDF Title
2	National foreword
6	Annex ZA (informative) Relationship between this European Standard and the essential requirements of Regulation (EU) 2016/426 aimed to be covered Annex ZA (informative) Relationship between this European Standard and the essential requirements of Regulation (EU) 2016/426 aimed to be covered Annex ZA (informative) Relationship between this European Standard and the essential requirements of Regulation (EU) 2016/426 aimed to be covered
10	European foreword
11	Introduction
13	1 Scope 2 Normative references 3 Terms and definitions
18	4 Classification 4.1 Classes of control
19	4.2 Groups of control 4.3 Classes of control functions 4.4 Types of DC supplied controls 5 Units of measurement and test conditions 6 Design and Construction 6.1 General 6.2 Mechanical parts of the control 6.2.1 Appearance 6.2.2 Holes 6.2.3 Breather holes 6.2.4 Screwed fastenings 6.2.5 Jointing 6.2.6 Moving parts
20	6.2.7 Sealing caps 6.2.8 Dismantling and reassembly 6.2.9 Auxiliary canals and orifices 6.2.10 Presetting device 6.2.101 Operating parts of taps 6.3 Materials 6.3.1 General material requirements 6.3.2 Housing 6.3.3 Zinc alloys 6.3.4 Springs 6.3.5 Resistance to corrosion and surface protection
21	6.3.6 Impregnation 6.3.7 Seals for glands for moving parts 6.3.101 Tap closure member 6.4 Gas connections 6.5 Electrical parts of the control 6.6 Protection against internal faults for the purpose of functional safety 6.101 Component parts 6.101.1 General 6.101.2 Turning angles
22	6.101.3 Lubrication 6.101.4 Stops 6.101.5 Safety lock
23	6.101.6 Bearing seal 6.101.7 Taper angle 6.101.8 Open and closed position of a tap 6.101.9 Compensation means for taps 6.101.10 Spring effect in taps 7 Performance 7.1 General 7.2 Leak-tightness 7.3 Torsion and bending 7.4 Rated flow rate 7.4.1 Requirements 7.4.2 Test
24	7.4.3 Conversion of air flow rate 7.5 Durability 7.6 Performance tests for electronic controls 7.7 Long-term performance for electronic controls 7.8 Data exchange 7.101 Operating torque and force 7.101.1 Requirements for operating torque 7.101.2 Test for operating torque 7.101.3 Requirements for operating force
25	7.101.4 Test for operating force 7.101.5 Requirements for operating torque for safety lock 7.101.6 Test for operating torque for safety lock 7.102 Endurance 7.102.1 Requirement 7.102.2 Endurance test
26	8 Electrical requirements 9 Electromagnetic compatibility (EMC) 10 Marking, instructions 10.1 Marking 10.2 Instructions
27	10.3 Warning notice
30	Bibliography
31	Annex A (informative) Abbreviations and symbols
32	Annex B (informative) Leak-tightness test for gas controls – volumetric method
33	Annex C (informative) Leak-tightness test for gas controls – pressure loss method
34	Annex D (normative) Calculation of pressure loss into leakage rate
35	Annex E (normative) Electrical/electronic component fault modes
36	Annex F (normative) Additional requirements for safety accessories and pressure accessories as defined in EU Directive 2014/68/EU
37	Annex G (normative) Materials for pressurized parts
38	Annex H (normative) Additional materials for pressurized parts
39	Annex I (normative) Requirements for controls used in DC supplied burners and appliances burning gaseous or liquid fuels
40	Annex J (normative) Method for the determination of a Safety Integrity Level (SIL)
41	Annex K (normative) Method for the determination of a Performance Level (PL)
42	Annex L (informative) Relationship between Safety Integrity Level (SIL) and Performance Level (PL)
43	Annex M (normative) Reset functions
44	Annex N (informative) Guidance document on Environmental Aspects
45	Annex O (normative) Seals of elastomer, cork and synthetic fibre mixtures

Additional information

Status	Withdrawn
Title	Manually operated taps for gas burning appliances
Replaces	BS EN 1106:2010
Publisher	BSI
Committee	GSE/22
Pages	46
Publication Date	2022-10-31
Withdrawn Date	2024-01-12
ISBN	978 0 539 06238 0
Standard Number	BS EN 1106:2022
Identical National Standard Of	EN 1106
Descriptors	Gas appliances, Gas cookers, Gas cylinder connections, Gas fittings, Testing, Taps (valves)
ICS Codes	23.060.40 - Pressure regulators

Preview PDF


PDF Format	Searchable	Printable	Preview Now

BS EN 1106:2022

PDF Catalog

Related products