ASTM-B694 2010(Redline)

$26.65

B694-10 Standard Specification for Copper, Copper-Alloy, Copper-Clad Bronze (CCB), Copper-Clad Stainless Steel (CCS), and Copper-Clad Alloy Steel (CAS) Sheet and Strip for Electrical Cable Shielding (Redline)

Published By	Publication Date	Number of Pages
ASTM	2010	11

Guaranteed Safe Checkout

Category: ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

Abstract

This specification establishes the requirements for sheets and strips of various thicknesses produced from copper (Copper UNS No. C1000), copper-iron alloy (Copper Alloy UNS No. C19400), copper-zinc alloy that is commercial bronze (Copper Alloy UNS No. C22000), copper-zinc alloy that is red brass (Copper Alloy UNS No. C23000), copper-zinc-iron-cobalt alloy (Copper Alloy UNS No. C66400), copper-zinc-iron alloy (Copper Alloy UNS No. C66410), copper-zinc-iron-tin alloy (Copper Alloy UNS No. C66430), cupro-20% nickel (Copper Alloy UNS No. C71000), copper-clad bronze, copper-clad stainless steel, and copper-clad alloy steel. These materials are intended for use as electrostatic or electromagnetic shielding for insulated power, control, instrumentation, and communication cables. Cladding metals may be bonded to the specified base metal by any method that will produce products that will conform to the properties and characteristics prescribed herein. Materials shall be furnished specific to individual metals in the following tempers: H00 (cold-rolled, 1/8 hard), H01 (cold-rolled, ¼ hard), H02 (cold-rolled, ½ hard); O61 (annealed), O81 (annealed, ¼ hard), O50 (light annealed), O61 (annealed, soft), OS035, and OS015. Specimens shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional (mass, thickness, width, straightness, and cladding ratio), mechanical (tensile strength, and Rockwell hardness), electrical (mass resistivity, and conductivity), chemical composition, and grain size requirements.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification establishes the requirements for copper, copper alloy, copper-clad bronze (CCB), copper-clad stainless steel (CCS), and copper-clad alloy steel (CAS) materials, sheet, and strip, in various thicknesses, for use as electrostatic or electromagnetic shielding for insulated power, control, instrumentation, and communication cables.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A176 Specification for Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and Strip A505 Specification for Steel, Sheet and Strip, Alloy, Hot-Rolled and Cold-Rolled, General Requirements for B152/B152M Specification for Copper Sheet, Strip, Plate, and Rolled Bar B248 Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar B601 Classification for Temper Designations for Copper and Copper Alloys–Wrought and Cast B736 Specification for Aluminum, Aluminum Alloy and Aluminum-Clad Steel Cable Shielding Stock B846 Terminology for Copper and Copper Alloys E3 Guide for Preparation of Metallographic Specimens E8 Test Methods for Tension Testing of Metallic Materials E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys E112 Test Methods for Determining Average Grain Size E255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition E478 Test Methods for Chemical Analysis of Copper Alloys

International Standards Organization (ISO) Standards

ISO3110/2 Determination of Aluminum; Flame Atomic Absorption Spectrometric Method (TC/26 Ref. No. N698 E/F) Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.

Keywords

bimetallic; cladding ratio; copper; copper alloy; copper-clad bronze; copper-clad alloy steel; copper-clad stainless steel; electric cable shielding; electrical conductivity; grain size; Rockwell Hardness; sheet; strip; tensile; UNS No. C11000; UNS No. C19400; UNS No. C22000; UNS No. C23000; UNS No. C64785; UNS No. C66400; UNS No. C66410; UNS No. C66430; UNS No. C71000; UNS No. G41300; UNS No. S43000; Brass plate/sheet/strip/rolled bar; Cable shielding; Cladding ratio; Communications–specifications; Copper alloy plate/sheet/strip/rolled bar–specifications; Copper-clad materials–specifications; Electrical conductivity; Electrical insulating solids–specifications; Electrical shielding cable–specifications; Stainless steel cladding; UNS C11000 (electrolytic tough pitch coper (ETP)); UNS C19400 (high copper alloy); UNS C22000 (commercial bronze, 80%); UNS C66400 copper alloy; UNS C66410 (misc. copper-zinc alloy); UNS C71000; ICS Number Code 3000

ICS Code

DOI: 10.1520/B0694-10 ASTM International is a member of CrossRef.

ASTM B694 (Copper Standards)

Citing ASTM Standards

[Back to Top]

Additional information

Standard Title	B694-10 Standard Specification for Copper, Copper-Alloy, Copper-Clad Bronze (CCB), Copper-Clad Stainless Steel (CCS), and Copper-Clad Alloy Steel (CAS) Sheet and Strip for Electrical Cable Shielding (Redline)
Published Code	ASTM
Publication Date	2010
Pages Count	11

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-B694 2010(Redline)

ASTM B694 (Copper Standards)

Related products