🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
ASTM-D3381:2012 Edition(Redline)

ASTM-D3381:2012 Edition(Redline)

$23.40

D3381/D3381M-12 Standard Specification for Viscosity-Graded Asphalt Cement for Use in Pavement Construction (Redline)

Published By Publication Date Number of Pages
ASTM 2012 3
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Abstract

This specification covers three sets of physical requirement limits for asphalt cements graded by viscosity at a specified temperature for use in pavement construction. The purchaser shall indicate the applicable table of limits. The cements shall be prepared from crude petroleum by suitable methods, and if needed, volume corrections should be made as well. The properties for which the materials shall be tested on and should conform to are water content, viscosity, penetration, Cleveland open cup flash point, solubility in trichloroethylene, ductility, and behavior during thin-film oven and rolling thin-film oven tests on residue.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers asphalt cements graded by viscosity at 60°C [140°F] for use in pavement construction. Three sets of limits are offered in this specification. The purchaser shall specify the applicable table of limits. In the event the purchaser does not specify limits, Table 1 shall apply. For asphalt cements graded by penetration at 25°C [77°F]. See Specification D946 . If needed, volume corrections for asphalt cements should be made according to Practice D4311 .

TABLE 1 Requirements for Asphalt Cement, Viscosity Graded at 60°C [140°F]
Note 1 — Grading based on original asphalt.
A  If ductility is less than 100, material will be accepted if ductility at 15°C [60°F] is 100 minimum at a pull rate of 5 cm/min.

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D5 Test Method for Penetration of Bituminous Materials

D36 Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)

D70 Test Method for Density of Semi-Solid Bituminous Materials (Pycnometer Method)

D92 Test Method for Flash and Fire Points by Cleveland Open Cup Tester

D95 Test Method for Water in Petroleum Products and Bituminous Materials by Distillation

D113 Test Method for Ductility of Bituminous Materials

D140 Practice for Sampling Bituminous Materials

D946 Specification for Penetration-Graded Asphalt Cement for Use in Pavement Construction

D1754 Test Method for Effects of Heat and Air on Asphaltic Materials (Thin-Film Oven Test)

D2042 Test Method for Solubility of Asphalt Materials in Trichloroethylene

D2170 Test Method for Kinematic Viscosity of Asphalts (Bitumens)

D2171 Test Method for Viscosity of Asphalts by Vacuum Capillary Viscometer

D2872 Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test)

D4311 Practice for Determining Asphalt Volume Correction to a Base Temperature

Keywords

asphalt cement; bitumen; pavement; viscosity;

ICS Code

ICS Number Code 93.080.20 (Road construction materials)

DOI: 10.1520/D3381_D3381M-12 ASTM International is a member of CrossRef.

Citing ASTM Standards

[Back to Top]

Related products

ASTM-D3381
$23.40