🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN 1455-1:2022:2023 Edition

BS EN 1455-1:2022:2023 Edition

$167.15

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Acrylonitrile-butadiene-styrene (ABS) – Specifications for pipes, fittings and the system

Published By Publication Date Number of Pages
BSI 2023 44
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) piping systems intended for soil and waste discharge applications (low and high temperature): – inside buildings (application area code “B”); – for both inside buildings and buried in ground within the building structure (application area code “BD”). NOTE 1 The intended use is reflected in the marking of products by “B” or “BD”. NOTE 2 Application “B” covers uses above ground inside buildings, or outside buildings fixed onto the wall. NOTE 3 Pipes and fittings of the pipe series S 25 are intended to be used for application area “B” only. NOTE 4 For use buried in ground within the building structure are intended only those components (marked with “BD”) with nominal outside diameters equal to or greater than 75 mm. NOTE 5 EN 476 [5] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this document fully meet these requirements. This document is also applicable to ABS and ASA pipes, fittings and the system intended for the following purposes: – ventilating part of the pipework in association with discharge applications; – rainwater pipework within the building structure. It also specifies the test parameters for the test methods that are referred to. This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours. NOTE 6 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 7 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.

PDF Catalog

PDF Pages PDF Title
2 undefined
8 1 Scope
2 Normative references
10 3 Terms and definitions
13 4 Symbols and abbreviations
14 5 Material
5.1 General
5.2 Additional material requirements for BD application
15 5.3 Fabricated fittings
5.4 Utilization of non-virgin material
5.5 Sealing ring retaining means
6 General characteristics
6.1 Appearance
6.2 Colour
6.3 External above ground application
6.4 Reaction to fire
7 Geometrical characteristics
7.1 General
7.2 Dimensions of pipes
7.2.1 Outside diameters
16 7.2.2 Length of pipes
17 7.2.3 Chamfering
7.2.4 Wall thickness
18 7.2.5 Dimensions of sockets
19 7.3 Dimensions of fittings
7.3.1 General
20 7.3.2 Outside diameters
7.3.3 Design lengths (Z)
7.3.4 Wall thicknesses
21 7.4 Dimensions of sockets and spigots
7.4.1 Classification and designation of sockets
7.4.1.1 General
7.4.1.2 Ring seal sockets
7.4.1.3 Adhesive joint sockets
7.4.1.4 Dual purpose sockets
22 7.4.2 Dimensions of ring seal sockets and spigots
7.4.2.1 Diameters and lengths
25 7.4.2.2 Wall thicknesses of ring seal sockets
26 7.4.3 Dimensions of adhesive joint sockets and spigots
7.4.3.1 Diameters and lengths
28 7.4.3.2 Wall thicknesses of adhesive joint sockets
7.5 Types of fittings
32 8 Mechanical characteristics
8.1 General characteristics
34 8.2 Additional mechanical requirements
35 8.3 Mechanical characteristics of fittings
8.3.1 General
8.3.2 Additional requirements of fittings intended for application area BD
36 9 Physical characteristics
9.1 Physical characteristics of pipes
38 9.2 Physical characteristics of fittings
39 10 Performance requirements
11 Sealing rings
40 12 Adhesives
13 Marking
13.1 General
13.2 Minimum required marking of pipes
41 13.3 Minimum required marking of fittings
13.4 Additional marking
42 Annex A (informative)Product standards

Related products

BS EN 1455-1:2022
$167.15