🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN 16062:2023 – TC

BS EN 16062:2023 – TC

$246.62

Tracked Changes. Intelligent transport systems. ESafety. eCall high level application requirements (HLAP) using GSM/UMTS circuit switched networks

Published By Publication Date Number of Pages
BSI 2023 122
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

In respect of pan-European eCall (operating requirements defined in EN 16072), this European Standard defines the high level application protocols, procedures and processes required to provide the eCall service using a TS12 emergency call over a mobile communications network. NOTE 1 The objective of implementing the pan-European in-vehicle emergency call system (eCall) is to automate the notification of a traffic accident, wherever in Europe, with the same technical standards and the same quality of services objectives by using a PLMN (such as ETSI prime medium) which supports the European harmonized 112/E112 emergency number (TS12 ETSI/TS 122 003) and to provide a means of manually triggering the notification of an emergency incident. NOTE 2 HLAP requirements for third party services supporting eCall can be found in EN 16102, and have been developed in conjunction with the development of this work item, and is consistent in respect of the interface to the PSAP. This deliverable makes reference to those provisions but does not duplicate them.

PDF Catalog

PDF Pages PDF Title
1 30478733
75 A-30419089
76 undefined
83 1 Scope
2 Normative references
84 3 Terms and definitions
87 4 Symbols and abbreviations
88 5 Conformance
90 6 General overview of the eCall transaction for Pan European eCall
94 7 Requirements
7.1 General requirements
7.1.1 General
7.1.2 USIM
7.1.3 Enabled PSAP
7.1.4 IVS configured only for eCall
95 7.1.5 Self-test
7.1.6 Standby mode applicable to IVS configured for eCall only
7.2 Activation
7.2.1 Activation of pan-European eCall
96 7.2.2 Activation of a test eCall
7.3 Call set-up
7.3.1 General
7.3.2 IVS network access device (NAD) already registered on PLMN
7.3.3 eCall in progress
7.3.4 Network selection and registration
97 7.3.5 Authentication of the subscriber
7.3.6 eCall establishment
7.3.7 Cell localization (by network)
98 7.3.8 Manual termination of eCall by vehicle occupants before trigger confirmation
7.4 MSD transfer
7.4.1 General
7.4.1.1 General
99 7.4.1.2 PSAP PULL mode
7.4.1.3 PSAP PUSH mode
7.4.2 Send initiation signal from IVS eCall modem to PSAP
7.4.3 eCall modem synchronization
100 7.4.4 Request MSD by PSAP eCall modem to IVS eCall modem
7.4.5 Send MSD from vehicle IVS to PSAP eCall modem
7.4.6 Link layer error check
7.4.7 Link layer ACK from PSAP eCall modem to IVS eCall modem
101 7.5 Application layer acknowledgement (AL- ACK)
7.5.1 Following transmission of the MSD to the eCall PSAP application
7.5.2 PSAP acknowledges the MSD
7.5.3 No receipt of application layer ACK
7.5.4 Form of presentation of the AL-ACK
103 7.6 PSAP request “SEND MSD”
7.6.1 General
7.6.2 Before call clear-down
105 7.6.3 After call clear-down
7.7 (void)
7.8 Audio link to vehicle occupants
7.9 eCall clear-down
106 7.10 PSAP call back
7.11 Rerouting to another PSAP/emergency control centre
107 7.12 Handling non equipped situations / error cases
7.12.1 MSD not transmitted correctly
7.12.2 Network registration fails
7.12.3 Call failure before the MSD is sent and acknowledged
7.12.4 Mobile network not supporting eCall flag or not provided with routing tables
7.12.4.1 General
108 7.12.4.2 Route both eCalls and 112/E112 voice calls to a PSAP that is equipped to support the eCall service
7.12.4.3 Route both eCalls and 112/E112 voice calls to a PSAP not equipped to support the eCall service
7.12.5 PSAP modem failure
7.12.5.1 Before link layer ACK is sent
7.12.5.2 After link layer ACK is sent
7.12.5.3 After application ACK is sent
7.12.6 PSAP network/ICT failure
7.12.7 PSAP application failure
7.12.8 PSAP operator does not respond
109 7.12.9 No response if line engaged
7.12.10 MSD not sent
7.12.11 MSD not received
7.12.12 Audio link not established
110 7.12.13 Audio link established but subsequently fails
7.12.14 Re-attempt in case of interrupted call
7.12.15 Automatic repeat attempts
7.12.16 IVS NAD does not receive call clear-down
8 Third party services supported eCall (TPS-eCall)
111 9 Defences against attack (Security provisions)
10 Quality of service requirements
11 Test and conformance requirements
12 Marking, labelling and packaging
13 Declaration of patents and intellectual property
112 Annex A (normative)Table of timings
115 Annex B (informative)(void)
116 Annex C (informative)Test system strategies
C.1 General
C.2 Vehicle and PSAP equipment life cycle
117 C.3 Laboratory environment
C.4 OEM or third party test systems

Related products

BS EN 16062:2023 - TC
$246.62