🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS ISO 21100:2020

BS ISO 21100:2020

$198.66

Air cargo unit load devices. Performance requirements and test parameters

Published By Publication Date Number of Pages
BSI 2020 56
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This document specifies the minimum requirements for airworthiness approval of air cargo pallets, nets and containers, generally designated as air cargo unit load devices (ULD).

This document is intended to provide a uniform technical reference for air cargo unit load devices approval. As a prerequisite, it is presupposed that the applicable general civil aviation requirements and the aircraft manufacturer’s approved Weight and Balance Manual are followed.

This document defines the minimum performance requirements and test parameters for air cargo unit load devices requiring approval of airworthiness for installation in an approved aircraft cargo compartment and restraint system that complies with the cargo restraint and occupant protection requirements of EASA CS-25 or 14 CFR Part 25, except for the 9,0 g forward ultimate inertia force of § 25.561(b) (3) (ii).

This document applies to airworthiness approved air cargo unit load devices intended for carriage on board civil transport category airplanes type certificated under EASA CS-25 or 14 CFR Part 25, or equivalent.

This document exclusively applies to unit load devices airworthiness approval and testing parameters. It does not apply to aircraft design or aircraft operating requirements, which are provided by the approved Weight and Balance Manual for each aircraft type.

Other aspects that do not directly pertain to air cargo unit load devices airworthiness approval and testing are not covered by this document and are defined in other International Standards (see Bibliography), e.g.:

  1. ULD design specifications,

  2. ULD in service damage limits,

  3. ULD restraint malfunction limitations,

  4. ULD test methods,

  5. ULD load distribution models,

  6. ULD maximum allowable contours,

  7. ULD CG (centre for gravity) location control means,

  8. ULD pressure equalization methods,

  9. ULD utilization guidelines.

Air cargo unit load devices qualified prior to publication of this document were approved in accordance with the requirements of ISO 8097:2001. This document is intended as a TSO approval reference for all new models of unit load devices in the sizes and types it covers, in replacement of ISO 8097. For air cargo unit load devices the size or type of which is not covered in this document, see the requirements of ISO 8097:2001, if their size or type is contained therein, or other equivalent criteria, if not.

NOTE 1

ISO 8097 is based on USA National Aerospace Standard NAS 3610 revision 10:1990, Specification for Cargo Unit Load Devices.

NOTE 2

The requirements for cargo covers are not defined in this document, except insofar as net restraint is incorporated therein.

PDF Catalog

PDF Pages PDF Title
2 undefined
7 Foreword
8 Introduction
9 1 Scope
10 2 Normative references
3 Terms and definitions
11 4 Classification
4.1 Types
4.2 Sizes
12 4.3 Configurations
4.4 Forms
4.5 Classification identifier
5 Performance requirements
5.1 Materials
5.2 Fabrication methods and workmanship
5.3 Protection
13 5.4 Construction
5.5 Marking
5.6 Inspection provisions
5.7 Fire protection
5.8 Rapid decompression
5.9 Dimensions and tolerances
14 5.10 Strength
5.10.1 Ultimate load criteria
5.10.2 Restraint criteria
5.10.3 Pallets and nets
15 5.10.4 Base performance
5.11 Environmental degradation
6 Tests
6.1 Test requirements
6.2 Test parameters
6.3 Test methods
16 6.4 Test results
7 Additional information
7.1 Intended use
7.2 Unit load device capacities
7.3 Container contours
7.4 Pallet configurations
8 Unit load device configurations
8.1 General
18 8.2 ULD CONFIGURATION A7
19 8.3 ULD CONFIGURATION A8
20 8.4 ULD CONFIGURATION B7
21 8.5 ULD CONFIGURATION B8
22 8.6 ULD CONFIGURATION G1
23 8.7 ULD CONFIGURATION K4
24 8.8 ULD CONFIGURATION L5
26 8.9 ULD CONFIGURATION L6
28 8.10 ULD CONFIGURATION M4
29 8.11 ULD CONFIGURATION M5
30 8.12 ULD CONFIGURATION N1
31 8.13 ULD CONFIGURATION P1
32 8.14 ULD CONFIGURATION Q1
33 8.15 ULD CONFIGURATION R1
35 8.16 ULD CONFIGURATION S1
36 9 Testing restraint conditions
9.1 General
37 9.2 RESTRAINT CONDITION (RC) A1
38 9.3 RESTRAINT CONDITION (RC) A2
40 9.4 RESTRAINT CONDITION (RC) G
41 9.5 RESTRAINT CONDITION (RC) K
43 9.6 RESTRAINT CONDITION (RC) L
45 9.7 RESTRAINT CONDITION (RC) N
47 9.8 RESTRAINT CONDITION (RC) P
48 9.9 RESTRAINT CONDITION (RC) Q
51 9.10 RESTRAINT CONDITION (RC) R
53 Bibliography

Related products

BS ISO 21100:2020
$198.66