BS ISO 21308-5:2014
$198.66
Road vehicles. Product data exchange between chassis and body work manufacturers (BEP) – Coding of loader crane bodywork
| Published By | Publication Date | Number of Pages |
| BSI | 2014 | 62 |
The ISO 21308 series describes a generic system for the exchange of data between truck chassis manufacturers and bodywork manufacturers. It applies to commercial vehicles as defined in ISO 3833, having a maximum gross vehicle mass above 3 500 kg.
The process of exchanging the above information can involve
-
chassis manufacturers,
-
chassis importers,
-
chassis dealers,
-
one or more bodywork manufacturers, and
-
bodywork component suppliers, e.g. manufacturers of demountable bodies, cranes and loading equipment, and tipping equipment.
This part of ISO 21308 specifically describes the coding dimensions and other characteristics of loader cranes and auxiliary stabilizers, to ensure an efficient and unambiguous communication of installation data between the parties involved.
This part of ISO 21308 covers loader cranes as specified in ISO 15442, designed to be fitted on commercial vehicles (including trailers).
This part of ISO 21308 is not applicable to other load-lifting systems (e.g. tail lifts, hook loader systems).
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Introduction |
| 9 | Section sec_1 Section sec_2 Section sec_3 1 Scope 2 Normative references 3 Terms and definitions |
| 10 | Section sec_3.1 |
| 11 | Table tab_a Figure fig_1 Section sec_3.2 Section sec_3.3 Section sec_3.4 Section sec_3.5 |
| 12 | Section sec_3.6 Section sec_3.7 Section sec_3.8 Section sec_3.9 Section sec_3.10 Section sec_3.11 Section sec_3.12 Section sec_3.13 Section sec_3.14 Section sec_3.15 Section sec_3.16 |
| 13 | Section sec_3.17 Section sec_3.18 Section sec_3.19 Section sec_3.20 Section sec_3.21 Section sec_3.22 Section sec_3.23 Section sec_3.24 Section sec_3.25 Section sec_3.25.1 Section sec_3.25.2 |
| 14 | Section sec_3.25.3 Section sec_3.25.4 Section sec_3.26 Section sec_4 Section sec_4.1 4 Coding principles 4.1 BEP codes of loader cranes |
| 15 | Table tab_1 Section sec_4.2 4.2 Units of BEP code values |
| 16 | Section sec_4.3 Section sec_4.3.1 Figure fig_2 Section sec_4.3.2 4.3 References for measurements |
| 17 | Figure fig_3 |
| 18 | Figure fig_4 Section sec_4.3.3 |
| 19 | Figure fig_5 Section sec_4.3.4 |
| 20 | Figure fig_6 |
| 21 | Section sec_4.3.5 |
| 22 | Section sec_5 Section sec_5.1 5 Coding of geometrical data and space requirements 5.1 Mounting positions of crane and auxiliary stabilizers |
| 23 | Section sec_5.2 5.2 Dimensional interfaces for connections to sub-frame and chassis |
| 25 | Section sec_5.3 Section sec_5.3.1 Section sec_5.3.1.1 5.3 Crane base dimensions, stabilizers, and lower space requirements |
| 26 | Section sec_5.3.1.2 |
| 29 | Section sec_5.3.2 |
| 33 | Section sec_5.3.3 |
| 34 | Section sec_5.4 Section sec_5.4.1 5.4 Boom system dimensions and space requirements above mounting plane |
| 35 | Section sec_5.4.2 Section sec_5.4.2.1 |
| 37 | Section sec_5.4.2.2 |
| 38 | Section sec_5.4.2.3 |
| 40 | Section sec_5.4.3 |
| 41 | Section sec_5.4.4 |
| 43 | Section sec_5.5 Section sec_5.5.1 5.5 Crane slewing space requirements |
| 44 | Section sec_5.5.2 |
| 45 | Section sec_5.6 5.6 Auxiliary stabilizer dimensions |
| 49 | Section sec_6 Section sec_6.1 6 Coding of masses 6.1 Mass points in transport position |
| 51 | Section sec_6.2 6.2 Masses with distances in working mode for stability calculations |
| 53 | Section sec_7 Section sec_8 Section sec_8.1 7 Coding of forces and moments 8 Coding of general crane data 8.1 General crane data |
| 54 | Section sec_8.2 8.2 Mechanical interfaces |
| 55 | Section sec_8.3 8.3 Hydraulics equipment and interfaces |
| 56 | Section sec_8.4 Section sec_8.5 8.4 Electrical/electronic equipment and interfaces 8.5 Load lifting attachments |
| 57 | Annex sec_A Annex sec_A.1 Annex sec_A.2 Annex A (normative) XML coding related to this part of ISO 21308 |
| 59 | Reference ref_1 Reference ref_2 Bibliography |
