Shopping Cart

No products in the cart.

IEEE 1017.4-2023

$37.38

IEEE Recommended Practice for Testing and Rating of Electrical Submersible Pump Motors (Published)

Published By Publication Date Number of Pages
IEEE 2023
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

New IEEE Standard – Active. Procedures and test values for testing and rating of electrical submersible pump (ESP) motors as well as installation and handling practices are specified in this document. The specified procedures and test values apply to ESP motor systems rated 3kV through 8kV (phase to phase).

PDF Catalog

PDF Pages PDF Title
1 IEEE Std 1017.4ā„¢-2023 Front cover
2 Title page
4 Important Notices and Disclaimers Concerning IEEE Standards Documents
8 Participants
10 Introduction
12 Contents
14 1.ā€‚Overview
1.1ā€‚Scope
1.2ā€‚Purpose
1.3ā€‚Word usage
15 2.ā€‚Normative references
3.ā€‚Definitions
18 4.ā€‚Electrical measurements
4.1ā€‚General
4.2ā€‚Power supply used for electrical measurements
19 4.3ā€‚Instrument selection
4.4ā€‚Instrument transformers
4.5ā€‚Voltage
4.6ā€‚Current
4.7ā€‚Power
4.8ā€‚Resistance
20 5.ā€‚Mechanical measurements
5.1ā€‚Mechanical-output measurement methods
5.2ā€‚Brake
5.3ā€‚Dynamometer
6.ā€‚General considerations
6.1ā€‚Environmental influences
21 6.2ā€‚Test equipment
22 6.3ā€‚Equipment setup
6.4ā€‚Special fault-locating test equipment
23 6.5ā€‚Equipment maintenance
7.ā€‚Motor model and design parameters
7.1ā€‚Basic data
25 8.ā€‚Routine tests
8.1ā€‚Terminal/stator winding resistance
26 8.2ā€‚Insulation resistance test
8.3ā€‚Surge comparison test
8.4ā€‚Phase rotation
8.5ā€‚Hipot test
8.6ā€‚Factory acceptance test (idle test/no load test)
27 8.7ā€‚String test
28 8.8ā€‚Machine vibration measurements
9.ā€‚Motor design performance tests
9.1ā€‚Basis of tests
9.2ā€‚Load test
31 9.3ā€‚Tests with rotor locked
9.4ā€‚Correction to a specified temperature
32 10.ā€‚Efficiency tests
10.1ā€‚Applicable test standards
10.2ā€‚Types of losses
35 11.ā€‚Surge comparison testing
11.1ā€‚Turn-turn insulation failures
36 11.2ā€‚Description
11.3ā€‚Test conditions
37 11.4ā€‚High frequency test levels for new coils
38 12.ā€‚DC hi-pot test methods
12.1ā€‚Overview
12.2ā€‚Precautions
12.3ā€‚DC high potential tester (hi-pot)
39 12.4ā€‚Equipment setup
12.5ā€‚Procedures
40 12.6ā€‚Evaluation of dc hi-pot test results
13.ā€‚Vibration analysis and dynamic balancing
13.1ā€‚General
41 13.2ā€‚Vibration reduction
42 14.ā€‚Motor expected design life (thermal insulation rating) testing
14.1ā€‚Insulation aging concepts
43 14.2ā€‚Limiting temperatures and their measurements for EIS
44 14.3ā€‚Temperature classes of EIS
45 15.ā€‚Characteristics of connected drives
47 AnnexĀ A (informative) Bibliography
49 Back cover
IEEE 1017.4-2023
$37.38