ISO 3459:1976
$13.00
Polyethylene (PE) pressure pipes — Joints assembled with mechanical fittings — Internal under-pressure test method and requirement
| Published By | Publication Date | Number of Pages |
| ISO | 1976-10 | 4 |
Specification of the test method and apparatures for checking the leakproofness of assembled joints, when the external pressure is greater than the pressure within the pipe. The test shall be carried out at two levels of difference between external and internal pressures (0,01 and 0,08 MPa).
Related products
-
BS 4258-6:1976
Methods of test for phosphoric acid (orthophosphoric acid) for industrial use – Determination of arsenic…
-
BS 6824:1987
Specification for performance and test of braking systems for wheeled earth-moving machinery Published By Publication…
-
BS 5550-2.2.2:1978
Cinematography. 16 mm film. Image areas – Specification for dimensions and location of the projectable…
-
BS EN ISO 3450:2008 2009
Earth-moving machinery. Braking systems of rubber-tyred machines. Systems and performance requirements and test procedures Published…
-
BS 4931:1986
Methods for preparation, marking and measuring of textile fabrics, garments and fabric assemblies in tests…
-
IEEE 1003.1, 2004 Edition
IEEE Standard for Information Technology – Portable Operating System Interface (POSIX(TM)) – Base Definitions Published…
-
BS EN ISO 3759:1995:2005 Edition
Textiles. Preparation, marking and measuring of fabric specimens and garments in tests for determination of…
-
BS 639:1986
Specification for covered carbon and carbon manganese steel electrodes for manual metal-arc welding Published By…
-
ISO 3359:1975
Phosphoric acid for industrial use — Determination of arsenic content — Silver diethyldithiocarbamate photometric method…
-
BS 3680-8C:1980
Measurement of liquid flow in open channels. Measuring instruments and equipment – Calibration of rotating-element…
-
BS EN 13203-3:2010
Solar supported gas-fired domestic appliances producing hot water. Appliances not exceeding 70 kW heat input…
-
BS EN 910:1996
Destructive tests on welds in metallic materials. Bend tests Published By Publication Date Number of…
-
ISO 3458:1976
Assembled joints between fittings and polyethylene (PE) pressure pipes — Test of leakproofness under internal…
-
API MPMS 11.1.1-1980 (R1987)
Manual of Petroleum Measurement Standards Chapter 11.1 – Volume Correction Factors Volume I Table 5A…
-
BS 5114:1975
Specification for performance requirements for joints and compression fittings for use with polyethylene pipes Published…
-
BS EN ISO 3459:2015
Plastic piping systems. Mechanical joints between fittings and pressure pipes. Test method for leaktightness under…
-
ISO 3659:1977
Fruits and vegetables — Ripening after cold storage Published By Publication Date Number of Pages…
-
ASHRAE Fundamentals Handbook IP 2013
2013 ASHRAE Handbook – Fundamentals – IP Edition Published By Publication Date Number of Pages…
-
API MPMS 11.1.8-1980
Manual of Petroleum Measurement Standards Chapter 11.1 – Volume Correction Factors Volume VIII Table 53B…
-
BS 5072-5:1980
Methods of test for sodium fluoride for industrial use – Determination of iron content Published…
-
ISO 1459:1973
Metallic coatings — Protection against corrosion by hot dip galvanizing — Guiding principles Published By…
-
API MPMS 11.1.10-1980
Manual of Petroleum Measurement Standards Chapter 11.1 – Volume Correction Factors Volume X – Background,…
-
ISO 349:1975
Hard coal — Audibert-Arnu dilatometer test Published By Publication Date Number of Pages ISO 1975-01…
-
ISO 3429:1976
Fluorure de sodium principalement utilisé pour la production de l’aluminium — Dosage du fer —…
-
BS EN ISO 3451-4:2000
Plastics. Determination of ash – Polyamides Published By Publication Date Number of Pages BSI 2000…
-
BS EN 1321:1997:2004 Edition
Destructive test on welds in metallic materials. Macroscopic and microscopic examination of welds Published By…
-
API MPMS 11.1.7-1980 (R1987)
Manual of Petroleum Measurement Standards Chapter 11.1 – Volume Correction Factors Volume VII Table 53A…
-
API MPMS 11.1.14-1982
Manual of Petroleum Measurement Standards Chapter 11.1-Volume Correction Factors, Volume XIV, Table 53D- Generalized Lubricating…
-
ISO 3409:1975
Voitures particulières — Positionnement transversal des commandes au pied Published By Publication Date Number of…
-
BS 308-3:1972:1976 Edition
Engineering drawing practice. – Geometrical tolerancing Published By Publication Date Number of Pages BSI 1976…
-
BS 308-2:1985
Engineering drawing practice – Recommendations for dimensioning and tolerancing of size Published By Publication Date…
-
ISO 3456:1975
Aircraft — Lever-operated manual switches (Class 3) — Performance requirements Published By Publication Date Number…
-
BS EN ISO 3451-4:1996:1991 Edition
Plastics. Determination of ash – Polyamides Published By Publication Date Number of Pages BSI 1991…
-
API MPMS 11.1.6-1980 (R1987)
Manual of Petroleum Measurement Standards Chapter 11.1 – Volume Correction Factors Volume VI Table 24C…
-
BS EN ISO 3451-5:1997:1991 Edition
Plastics. Determination of ash – Poly(vinyl chloride) Published By Publication Date Number of Pages BSI…
-
BS EN ISO 604:1997:1993 Edition
Plastics. Determination of compressive properties Published By Publication Date Number of Pages BSI 1993 20
-
AS 3778.6.3:1992
Measurement of water flow in open channels – Measuring devices, instruments and equipment – Calibration…
-
API MPMS 11.1.13-1982
Manual of Petroleum Measurement Standards Chapter 11.1 – Volume Correction Factors Volume XIII Table 5D-Generalized…
-
ISO 3559:1976
Road vehicles — Working voltages for lights fitted to motor vehicles and to their trailers…
-
ISO 3959:1977
Bananes vertes — Conditions de maturation Published By Publication Date Number of Pages ISO 1977-06…