New IEEE Standard – Active. Uniform procedures for the measurement of radio noise generated by corona from overhead power lines and substations are established in this standard. Measurement procedures in this standard are also valid for otherre power-line noise sources such as gaps and harmonics; however, most of the precautionary information, analysis, and data plotting techniques were written and developed primarily for corona discharges. The procedures are not valid for measuring transient radio noise sources that occur during breaker or disconnect switching operations. The procedures apply in the frequency range of 0.010 MHz to 1000 MHz; however, the emphasis is on the standard amplitude-modulation broadcasting (0.535 MHz to 1.605 MHz) and television broadcasting (54 MHz to 72 MHz, 76 MHz to 88 MHz, 174 MHz to 216 MHz, and 470 MHz to 698 MHz) bands. This standard is applicable to both ac and dc transmission lines and substations.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 1<\/td>\n | IEEE Std 430\u2122-2017 Front cover <\/td>\n<\/tr>\n | ||||||
| 2<\/td>\n | Title page <\/td>\n<\/tr>\n | ||||||
| 4<\/td>\n | Important Notices and Disclaimers Concerning IEEE Standards Documents <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | Participants <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | Introduction <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | Contents <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 1.\u2002Scope 2.\u2002Normative references <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 3.\u2002Definitions 4.\u2002Measuring instrumentation 4.1\u2002Radio-noise and field-strength meter <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 4.2\u2002Radio-noise meter calibration 4.3\u2002Detector function selection 4.4\u2002Units of measurements 4.5\u2002Monitoring 5.\u2002Measurement of radio noise (0.010 MHz to 30 MHz) from overhead power lines 5.1\u2002Test sites <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 5.2\u2002Measurement procedure <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 5.3\u2002Background data <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | 6.\u2002Measurement of radio noise (30 MHz to 1000 MHz) from overhead power lines 6.1\u2002Introduction 6.2\u2002Test sites 6.3\u2002Measurement procedure <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | 7.\u2002Precautions in measurements 7.1\u2002Location of personnel and equipment 7.2\u2002Standing waves 7.3\u2002Background noise 7.4\u2002Weather <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | 7.5\u2002Selection of antennas <\/td>\n<\/tr>\n | ||||||
| 27<\/td>\n | 7.6\u2002Additional precautions 8.\u2002Measurement of radio noise (0.010 MHz to 30 MHz) from substations 8.1\u2002Test sites 8.2\u2002Measurement procedure <\/td>\n<\/tr>\n | ||||||
| 28<\/td>\n | 8.3\u2002Reporting of data 9.\u2002Measurement of radio noise (30 MHz to 1000 MHz) from substations 9.1\u2002Introduction <\/td>\n<\/tr>\n | ||||||
| 29<\/td>\n | Annex\u00a0A (informative) Bibliography <\/td>\n<\/tr>\n | ||||||
| 30<\/td>\n | Annex\u00a0B (informative) Vehicle-mounted antennas B.1\u2002General B.2\u2002Measuring broadcast signals B.3\u2002Measuring radio noise <\/td>\n<\/tr>\n | ||||||
| 31<\/td>\n | Annex\u00a0C (informative) Application of measured signals and noise in transmission line design C.1\u2002General C.2\u2002Comparison pre- and post-construction C.3\u2002Determining expected reception effects <\/td>\n<\/tr>\n | ||||||
| 34<\/td>\n | Back cover <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" IEEE Standard Procedures for the Measurement of Radio Noise from Overhead Power Lines and Substations<\/b><\/p>\n |