| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 1<\/td>\n | 30442635 <\/td>\n<\/tr>\n | ||||||
| 51<\/td>\n | A-30432133 <\/td>\n<\/tr>\n | ||||||
| 55<\/td>\n | Foreword <\/td>\n<\/tr>\n | ||||||
| 57<\/td>\n | 1 Scope 2 Normative references <\/td>\n<\/tr>\n | ||||||
| 58<\/td>\n | 3 Terms and definitions <\/td>\n<\/tr>\n | ||||||
| 59<\/td>\n | Figure 1 \u2014 Typical geometric form for an egg-shaped bore 4 Symbols Table 1 \u2014 Symbols 5 General requirements 5.1 Application <\/td>\n<\/tr>\n | ||||||
| 60<\/td>\n | 5.2 Concrete (4.2) \u2013 composition 5.3 Finish (4.3.2) 5.4 Geometrical characteristics (4.3.3) <\/td>\n<\/tr>\n | ||||||
| 61<\/td>\n | Table 2 \u2014 Nominal sizes and tolerances of units with a circular bore, for use in a trench <\/td>\n<\/tr>\n | ||||||
| 62<\/td>\n | Table 3 \u2014 Nominal sizes and tolerances of egg-shaped units Table 4 \u2014 Nominal sizes, internal manufacturing diameter and tolerances of jacking pipes <\/td>\n<\/tr>\n | ||||||
| 63<\/td>\n | Table 5 \u2014 Tolerances on the squareness of ends of jacking pipes <\/td>\n<\/tr>\n | ||||||
| 64<\/td>\n | 5.5 Durability of joints (4.3.4.2) 5.6 Crushing strength (4.3.5) Table 6 \u2014 Minimum crushing loads for strength class 120 units with a circular bore for use in a trench <\/td>\n<\/tr>\n | ||||||
| 65<\/td>\n | Table 7 \u2014 Minimum crushing loads for strength class 150 egg-shaped units <\/td>\n<\/tr>\n | ||||||
| 66<\/td>\n | Table 8 \u2014 Minimum crushing loads for strength class 120 jacking pipes 5.7 Resistance to high pressure jetting 5.8 Lifting anchorages 5.9 Bends (4.3.3.3) <\/td>\n<\/tr>\n | ||||||
| 67<\/td>\n | 6 Special requirements – reinforced concrete units (Concrete cover) (5.2.2) 7 Conformity evaluation 7.1 Application 7.2 Finish 7.3 Geometrical characteristics 7.4 Lifting anchorages 8 Marking <\/td>\n<\/tr>\n | ||||||
| 68<\/td>\n | Annex A (normative)\u2002 British Standards relevant to BS EN 1916:2002 Table A.1 \u2014 British Standards relevant to BS EN 1916:2002 Annex B (informative)\u2002 Information to be supplied in an enquiry or order <\/td>\n<\/tr>\n | ||||||
| 69<\/td>\n | Table B.1 \u2014 Information to be supplied in an enquiry or order Annex C (normative)\u2002 Surface finish tests Figure C.1 \u2014 Gauge for assessing surface evenness <\/td>\n<\/tr>\n | ||||||
| 70<\/td>\n | Figure C.2 \u2014 Gauge for assessing surface voids Annex D (normative)\u2002 Dimensional tests <\/td>\n<\/tr>\n | ||||||
| 72<\/td>\n | Figure D.1 \u2014 Gauge for measuring deviation from straightness <\/td>\n<\/tr>\n | ||||||
| 73<\/td>\n | Figure D.2 \u2014 Measurement of internal lengths and diagonals of a jacking pipe Figure D.3 \u2014 Squareness of ends across a diameter of a jacking pipe <\/td>\n<\/tr>\n | ||||||
| 74<\/td>\n | Annex E (normative)\u2002 Test for resistance to high pressure jetting <\/td>\n<\/tr>\n | ||||||
| 75<\/td>\n | Figure E.1 \u2014 Nozzle geometry <\/td>\n<\/tr>\n | ||||||
| 77<\/td>\n | Annex F (normative)\u2002 Lifting anchorage pull-out test Figure F.1 \u2014 Diagram of typical anchorage pull-out testing machine on longitudinal section of unit wall <\/td>\n<\/tr>\n | ||||||
| 79<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Tracked Changes. Concrete pipes and ancillary concrete – Unreinforced and reinforced concrete pipes (including jacking pipes) and fittings with flexible joints (complementary to BS EN 1916:2002). Specification<\/b><\/p>\n |