Clause 1 of IEC 61439-1:2020 is applicable except as follows. Replacement: This part of IEC 61439 defines the specific requirements for Assemblies for the following applications: marinas, camping sites, market squares and electric vehicle charging stations as follows: – Assemblies for which the rated voltage does not exceed 1 000 V AC or 1 500 V DC; – Assemblies intended for use in connection with the generation, transmission, distribution and conversion of electric energy, and for the control of electric energy consuming equipment; – Assemblies operated by ordinary persons (e.g. to plug and unplug of electrical equipment); – Assemblies intended to be installed and used in market squares, marinas, camping sites and other similar sites accessible to the public including temporary installations; – Assemblies intended for charging stations for electric vehicles (AEVCS) for Mode 3 and Mode 4. They are designed to integrate the functionality and additional requirements for electric vehicle conductive charging systems according to IEC 61851-1:2017. NOTE 1 Throughout this document, the terms AMHS (see 3.1.701), ACCS (see 3.1.702), AMPS (see 3.1.703), AEVCS (see 3.1.704) are used for low-voltage switchgear and controlgear assemblies intended for use respectively in marinas and similar locations (AMHS), camping sites and similar locations (ACCS), market squares and other similar external public sites (AMPS) and charging stations (AEVCS). The term assemblies is used for indicating all these boards. This standard is not applicable to assemblies intended to be installed on board of ships, houseboats, pleasure crafts and similar vessels. For the correct selection of the switching devices and components, the following standards apply: – IEC 60364-7-709 (AMHS) or – IEC 60364-7-708 (ACCS) or – IEC 60364-7-740 (AMPS) or – IEC 60364-7-722 (AEVCS). This document applies to all assemblies whether they are designed, manufactured and verified on a one-off basis or fully standardised and manufactured in quantity. The manufacturing and\/or assembling may be carried out other than by the original manufacturer (see 3.10.1 of IEC 61439-1:2020). This document does not apply to individual devices and self-contained components such as circuit breakers, fuse switches, electronic equipment, which comply with their relevant product standards. NOTE 2 Where electrical equipment is directly connected to public low-189 voltage supply system and equipped with an energy meter for billing of the legal provider of the low-voltage supply, additional particular requirements based on national regulations apply, if any. This document does not apply to boxes and enclosures for electrical accessories for household and similar fixed electrical installations as defined in IEC 60670-24.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 2<\/td>\n | undefined <\/td>\n<\/tr>\n | ||||||
| 5<\/td>\n | Annex ZA (normative)Normative references to international publicationswith their corresponding European publications <\/td>\n<\/tr>\n | ||||||
| 6<\/td>\n | English CONTENTS <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | FOREWORD <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 1 Scope <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 2 Normative references 3 Terms and definitions <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 4 Symbols and abbreviations 5 Interface characteristics <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 6 Information <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 7 Service conditions 8 Constructional requirements <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 9 Performance requirements 10 Design verification <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | Figures Figure 701 \u2013 Diagram of test to verify the resistance to static load <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | Figure 702 \u2013 Diagram of test to verify the mechanical strength of doors <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | Figure 703 \u2013 Sandbag for test to verify the resistance to shock load <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | Figure 704 \u2013 Diagram of test to verify resistance to shock load <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | Figure 705 \u2013 Diagram of test to verify resistance to torsional stress <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | 11 Routine verification Tables Table 701 \u2013 Values of assumed loading <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | Table 702 \u2013 Mechanical tests <\/td>\n<\/tr>\n | ||||||
| 28<\/td>\n | Annex AA (informative) User information template Table AA.1 \u2013 User information template <\/td>\n<\/tr>\n | ||||||
| 32<\/td>\n | Annex BB (informative) Design verification Table BB.1 \u2013 List of design verifications to be performed <\/td>\n<\/tr>\n | ||||||
| 33<\/td>\n | Annex CC (normative) Endurance of the individual switching device <\/td>\n<\/tr>\n | ||||||
| 35<\/td>\n | Figure CC.1 \u2013 Test circuit for endurance of the individual switching device test <\/td>\n<\/tr>\n | ||||||
| 36<\/td>\n | Figure CC.2 \u2013 Informative wave shape of inrush currentfor tests in accordance with Annex CC <\/td>\n<\/tr>\n | ||||||
| 37<\/td>\n | Annex DD (informative) Examples of assemblies in accordance with 5.701.1.1 Figure DD.1 \u2013 Examples of assemblies according to 5.701.1.1 <\/td>\n<\/tr>\n | ||||||
| 38<\/td>\n | Annex EE (informative) Verification of resistance to mechanical shock impacts induced by sharp edged objects Figure EE.1 \u2013 Striker element for test of resistance to mechanical shock impacts induced by sharp-edged objects <\/td>\n<\/tr>\n | ||||||
| 39<\/td>\n | Annex FF (informative) List of notes concerning certain countries <\/td>\n<\/tr>\n | ||||||
| 41<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Low-voltage switchgear and controlgear assemblies – Assemblies for specific applications such as marinas, camping sites, market squares, electric vehicle charging stations<\/b><\/p>\n |