SMACNA RoundIndustrialDuctConstructionStandards 2013
$192.83
Round Industrial Duct Construction Standards, 3rd edition
| Published By | Publication Date | Number of Pages |
| SMACNA | 2013 | 660 |
The revised “Round Industrial Duct Construction Standard,” 3rd edition, 2013, an American National Standard, ANSI/SMACNA 005-2013, is now available. The standard expands the scope of the second edition, updating the duct materials to include aluminized steel, temperature correction factors for round industrial, and minimum decimal thickness for aluminum duct selection tables. Several chapters offer a standardized, engineering basis for design and construction of industrial duct of Class 1 to Class 5 air. A spiral duct chapter for Class 1 and Class 2 air covers design pressures ranging from 30 in. wg negative to 50 in. wg positive, plus carbon and galvanized steel tables. The 660 page-book includes expanded tables for stainless steel and aluminum, expanded tables for duct sizes up to 96 inches in diameter, plus Class 5 systems handling corrosives and spiral lock-seam pipe. Appendix chapters provide overviews of methods for including crawlspaces in the conditioned space and such HVAC accessories as UV lights, zoning, and advanced air filtering methods to enhance indoor environmental quality (IEQ) for occupants. More detailed information and new concepts are included in the 278-page publication for earth energy heat exchanger methods and ground source heat pumps. Updated construction code requirements are reflected throughout the range of HVAC system types along with energy efficiency and sustainable practices. Installation, operation, maintenance, and guidance for residential heating, ventilation, and air conditioning systems are also included.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | Halftitle page |
| 3 | Title page |
| 4 | Copyright page |
| 5 | FOREWORD |
| 7 | ROUND INDUSTRIAL DUCT CONSTRUCTION TASK FORCE FORMER COMMITTEE MEMBERS AND OTHER CONTRIBUTORS |
| 8 | NOTICE TO USERS OF THIS PUBLICATION |
| 11 | TABLE OF CONTENTS |
| 17 | CHAPTER 1 INTRODUCTION |
| 19 | 1.1 SCOPE 1.2 PURPOSE 1.3 DEVELOPMENT OF THE THIRD EDITION |
| 20 | 1.4 INDUSTRIAL DUCT DESIGN AVENUES 1.5 HOW TO USE THIS MANUAL |
| 21 | 1.6 MANUAL CONTENTS |
| 23 | CHAPTER 2 INDUSTRIAL DUCT APPLICATIONS |
| 25 | 2.1 INTRODUCTION 2.2 DEFINITION OF INDUSTRIAL DUCT 2.3 DUCT SYSTEM CLASSIFICATION |
| 26 | 2.4 MATERIAL (PARTICULATE) CHARACTERISTICS AND CLASSES |
| 35 | CHAPTER 3 DUCT MATERIALS |
| 37 | 3.1 INTRODUCTION 3.2 MATERIAL TYPES |
| 39 | 3.3 HOT–ROLLED (CARBON) STEEL DATA |
| 40 | 3.4 COLD–ROLLED (CARBON) STEEL DATA |
| 41 | 3.5 COATED CARBON STEEL (GALVANIZED AND ALUMINIZED) |
| 44 | 3.6 STAINLESS STEEL DATA |
| 48 | 3.7 ALUMINUM DATA |
| 50 | 3.8 MATERIAL PROPERTIES SUMMARY |
| 52 | 3.9 CORROSION |
| 55 | CHAPTER 4 DESIGN CRITERIA |
| 57 | 4.1 INTRODUCTION 4.2 GENERAL PROVISIONS 4.3 NOMENCLATURE |
| 59 | 4.4 LOADS |
| 61 | 4.5 LIMITS AND TOLERANCES 4.6 SERVICEABILITY AND DURABILITY |
| 62 | 4.7 STRENGTH PROVISIONS – DESIGN BASIS |
| 63 | 4.8 DESIGN OF CIRCUMFERENTIAL STIFFENERS |
| 64 | 4.9 CONNECTIONS |
| 65 | 4.10 HANGERS AND SUPPORTS 4.11 THERMAL EXPANSION |
| 71 | CHAPTER 5 COMMENTARY |
| 73 | 5.1 INTRODUCTION 5.2 LOADS |
| 76 | 5.3 LIMITS AND TOLERANCES 5.4 SERVICEABILITY AND DURABILITY |
| 77 | 5.5 STRENGTH PROVISIONS DESIGN BASIS |
| 80 | 5.6 DESIGN OF CIRCUMFERENTIAL STIFFENERS |
| 81 | 5.7 CONNECTIONS |
| 83 | 5.8 HANGERS AND SUPPORTS 5.9 THERMAL EXPANSION |
| 85 | CHAPTER 6 FLOW CHARTS |
| 87 | 6.1 INTRODUCTION 6.2 COMMENTARY 6.3 ASSUMPTIONS 6.4 FLOW CHARTS |
| 97 | CHAPTER 7 ILLUSTRATIVE EXAMPLES |
| 99 | 7.1 INTRODUCTION 7.2 COMMENTARY 7.3 NOMENCLATURE |
| 103 | EXAMPLE 7–1. COMPLEX LOAD COMBINATIONS |
| 111 | EXAMPLE 7–2. HIGH TEMPERATURE APPLICATION |
| 118 | EXAMPLE 7–3. MODERATE TEMPERATURE (ALUMINUM) APPLICATION |
| 125 | EXAMPLE 7–4. (CARBON STEEL) DUCT RISER IN AN OUTDOOR APPLICATION |
| 135 | CHAPTER 8 DUCT SELECTION TABLES CARBON AND COATED STEELS |
| 137 | 8.1 INTRODUCTION |
| 139 | 8.2 USE OF THE TABLES |
| 161 | EXAMPLE 8−1. MODIFYING PARTICULATE DENSITY TO ACCOUNT FOR INSULATION AND CLADDING GRAVITY LOADS |
| 190 | EXAMPLE 8–2. TYPICAL CARBON STEEL DUCT SELECTION EXAMPLE 8–3. TYPICAL GALVANIZED STEEL DUCT SELECTION |
| 191 | EXAMPLE 8–4. TYPICAL GALVANIZED STEEL DUCT SELECTION FOR A POSITIVE PRESSURE APPLICATION |
| 193 | CHAPTER 9 DUCT SELECTION TABLES STAINLESS STEEL |
| 195 | 9.1 INTRODUCTION |
| 197 | 9.2 USE OF THE TABLES |
| 228 | EXAMPLE 9–1. CLASS 5, STAINLESS STEEL DUCT CONVEYING CORROSIVE FUMES AT MODERATE TEMPERATURE |
| 229 | EXAMPLE 9–2. CLASS 1, STAINLESS STEEL DUCT FOR PROCESS EXHAUST AT HIGH TEMPERATURE |
| 230 | EXAMPLE 9–3. CLASS 5, STAINLESS STEEL DUCT CONVEYING CORROSIVES UNDER POSITIVE PRESSURE |
| 231 | CHAPTER 10 DUCT SELECTION TABLES ALUMINUM |
| 233 | 10.1 INTRODUCTION |
| 235 | 10.2 USE OF THE TABLES |
| 266 | EXAMPLE 10-1. TYPICAL ALUMINUM DUCT SELECTION FOR A CLASS 1 APPLICATION |
| 267 | EXAMPLE 10-2. TYPICAL ALUMINUM DUCT SELECTION FOR A CLASS 1 APPLICATION UNDER POSITIVE PRESSURE |
| 269 | CHAPTER 11 SELECTION TABLES SPIRAL LOCKSEAM PIPE |
| 271 | 11.1 INTRODUCTION |
| 273 | 11.2 COMMENTARY |
| 274 | 11.3 DESIGN CRITERIA FOR SPIRAL DUCTS |
| 275 | 11.4 USE GUIDELINES |
| 277 | 11.5 SPIRAL PIPE – CARBON AND COATED STEELS |
| 300 | 11.6 SPIRAL PIPE – STAINLESS STEEL |
| 312 | 11.7 SPIRAL PIPE – ALUMINUM |
| 324 | 11.8 POSITIVE PRESSURE SYSTEMS |
| 325 | 11.9 COMMENTARY ON STIFFENERS AND FLANGES |
| 331 | CHAPTER 12 STIFFENERS, FLANGES, AND FASTENERS |
| 333 | 12.1 INTRODUCTION AND SCOPE 12.2 SELECTION OF STIFFENERS |
| 360 | 12.3 SELECTION OF CONNECTING FLANGES |
| 391 | 12.4 SELECTION OF BOLTS FOR CONNECTING DUCT |
| 414 | 12.5 GASKETS, CAULKING, AND JOINT SEALANTS |
| 417 | CHAPTER 13 HANGERS AND SUPPORTS |
| 419 | 13.1 INTRODUCTION AND SCOPE 13.2 HANGERS AND SUPPORTS COMMENTARY 13.3 GENERAL GUIDELINES |
| 420 | 13.4 METHODS FOR HANGING AND SUPPORTING DUCT 13.5 DUCT HANGERS AND SUPPORTS |
| 509 | CHAPTER 14 WELDING |
| 511 | 14.1 INTRODUCTION 14.2 WELDED JOINT ACCEPTED INDUSTRY PRACTICE 14.3 WELDED JOINT CONSIDERATIONS |
| 515 | 14.4 WELDING PROCEDURES |
| 523 | 14.5 WELDING SYMBOLS |
| 529 | CHAPTER 15 ACCEPTED INDUSTRIAL CONSTRUCTION PRACTICES |
| 531 | 15.1 INTRODUCTION 15.2 ROUND PIPE COMMON SEAMS AND JOINTS 15.3 FABRICATION TOLERANCES |
| 539 | 15.4 FITTINGS |
| 545 | 15.5 STACKS |
| 553 | 15.6 STACK SAMPLING FACILITIES |
| 556 | 15.7 CLEANOUT DOORS/ACCESS OPENINGS |
| 560 | 15.8 DAMPERS AND GATES 15.9 CONNECTIONS AND EXPANSION JOINTS |
| 569 | 15.10 FAN INLET AND OUTLET CONDITIONS |
| 577 | CHAPTER 16 GUIDE SPECIFICATION |
| 579 | 16.1 INTRODUCTION 16.2 DRAWINGS 16.3 SEISMIC RESTRAINT PROVISIONS 16.4 GUIDE SPECIFICATION |
| 593 | APPENDIX A COMMENTARY ON FORMULA DERIVATIONS AND UNITS |
| 597 | APPENDIX B SUPPLEMENTARY DESIGN DATA |
| 613 | APPENDIX C COMMENTARY ON SURFACE PREPARATION TECHNIQUES |
| 617 | APPENDIX D REFERENCED DOCUMENTS |
| 623 | APPENDIX E RIDCS SOFTWARE USERS MANUAL |
| 643 | GLOSSARY |
| 653 | INDEX |
