| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 1<\/td>\n | BRITISH STANDARD <\/td>\n<\/tr>\n | ||||||
| 2<\/td>\n | Committees responsible for this British\ufffdStandard <\/td>\n<\/tr>\n | ||||||
| 3<\/td>\n | Contents <\/td>\n<\/tr>\n | ||||||
| 6<\/td>\n | Foreword Foreword to amendment A1 Foreword to amendment A2 <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | Contents <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 1 Scope 1.1 Normative references 2 Definitions 2.1 starter with mechanical switching element 2.2 starter with electronic switching element 2.3 deactivated lamp <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 2.4 non re-opening level 2.5 maximum abnormal current 2.6 starting aid 2.7 maximum case temperature ( 3 General requirements for tests 3.1 Only requirements for type tests are included. 3.2 Supply voltage 3.3 All starting devices specified in this standard shall meet the requirements of IEC 926. 3.4 All starting devices specified in this standard shall meet the requirements of IEC 61547. 4 Marking <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 5 Scope 6 Starting test 6.1 Starting test quantity 6.2 Conditions of acceptance 6.3 Conditions of test Table 1 Starting aid requirements <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 6.4 Starters having a mechanical switching element 6.5 Starters having an electronic switching element <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 6.6 Non-reoperating level 6.7 Maximum pre-heat current (lamp fails to start) 6.8 Interruption of starter function <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 7 Endurance test 7.1 Test quantity 7.2 Test conditions 7.3 Starters replaceable without tools 7.4 Starters not intended for replacement 7.5 Conditions of acceptance 8 Deactivated lamp test 8.1 Test quantity 8.2 Test conditions 8.3 Starters with a mechanical switching element but without cut-out 8.4 Starters with an electronic switching element but without cut-out <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 8.5 Starters with a mechanical switching element and with thermal cut-out 8.6 Starters with an electronic switching element and electronic cut-out 8.7 Condition of acceptance <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 9 Scope 10 Starting test 10.1 The test is made on two ignitors that have not been submitted to any other test. 10.2 Test conditions 10.3 Conditions of acceptance 10.4 Switching speed 10.5 Pulse voltage 10.6 Repetition rate, pulse position, width and height of starting pulse for triggered ignitors <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | 10.7 Ignition energy for non-triggered ignitors 11 Non-reoperating level 12 Endurance test 12.1 Test quantity 12.2 Test conditions 12.3 Ignitors without replaceable switching elements <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | 12.4 Ignitors with switching elements replaceable without tools 12.5 Ignitors with additional cut-outs 12.6 Conditions of compliance <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | Figure 1 Pulse voltage measurement for starting devices <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | Figure 2 Ignition energy measurement for non-triggered starting devices <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | Annex A (normative) Ballasts to be used for life testing A.1 It shall be of a type that will comply with the requirements of the relevant IEC ballast specific… A.2 When, at its rated voltage, it is associated with a lamp whose voltage at lamp terminals does not… Annex B (normative) Explanation of starting conditions for electronic starters with an electronic switchi… B.1 Introduction B.2 Characteristics which affect lamp starting B.3 \u201cWith starter\u201d methods of lamp starting <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | B.4 Interpretation of the requirements and information given on lamp data sheets <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | B.5 Open-circuit voltages and transition times\ufffd( B.6 Measurement requirements <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | B.7 Precautions to be observed if high-frequency voltages are produced by the electronic starter B.7.1 Starting aid spacing Figure B.1 Cathode heating current requirements for electronic starters with\ufffdelectronic\ufffdswitching element <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | Figure B.2 Interpretation of effective heating current <\/td>\n<\/tr>\n | ||||||
| 27<\/td>\n | Figure B.3 Interpretation of effective heating current <\/td>\n<\/tr>\n | ||||||
| 28<\/td>\n | Figure B.3.1 Starters which remove pre-heating current when open-circuit voltages\ufffdare\ufffdelevated Figure B.3.2 Starters which have open-circuit voltage transition times higher than 100 ms <\/td>\n<\/tr>\n | ||||||
| 29<\/td>\n | Annex C (informative) A guide to quoting product life and failure rate C.1 To allow the lifetime and failure rate of different electronic products to be meaningfully compar… C.2 The maximum surface temperature, symbol C.3 The failure rate, if the electronic product is operated continuously at the maximum temperature C.4 For the method used to obtain the information given in Clause\ufffd <\/td>\n<\/tr>\n | ||||||
| 30<\/td>\n | Annex ZA (normative) Normative references to international publications with their corresponding European … <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Specification for auxiliaries for lamps. Starting devices (other than glow starters). Performance requirements<\/b><\/p>\n |