{"id":461022,"date":"2024-10-20T10:13:26","date_gmt":"2024-10-20T10:13:26","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/astm-d2270-2024\/"},"modified":"2024-10-26T18:55:07","modified_gmt":"2024-10-26T18:55:07","slug":"astm-d2270-2024","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/astm\/astm-d2270-2024\/","title":{"rendered":"ASTM-D2270 2024"},"content":{"rendered":"

ASTM D2270-24<\/h3>\n

Redline Standard: Standard Practice for Calculating Viscosity Index from Kinematic Viscosity at 40\u2009\u00b0C and 100\u2009\u00b0C<\/h4>\n
\n

ASTM D2270<\/h4>\n

Scope<\/strong><\/p>\n

\n

1.1<\/span> This practice3<\/span><\/span> covers the procedures for calculating the viscosity index of petroleum products, such as lubricating oils, and related materials from their kinematic viscosities at 40\u2009\u00b0C and 100\u2009\u00b0C.<\/p>\n

\n

Note 1:<\/span> The results obtained from the calculation of VI<\/span> from kinematic viscosities determined at 40\u2009\u00b0C and 100\u2009\u00b0C are virtually the same as those obtained from the former VI<\/span> system using kinematic viscosities determined at 37.78\u2009\u00b0C and 98.89\u2009\u00b0C.<\/span><\/p>\n<\/p><\/div>\n<\/p><\/div>\n

\n

1.2<\/span> This practice does not apply to petroleum products with kinematic viscosities less than 2.0 mm2<\/sup>\/s at 100\u2009\u00b0C. Table\u20091 given in this practice applies to petroleum products with kinematic viscosities between 2\u2009mm2<\/sup>\/s and 70\u2009mm2<\/sup>\/s at 100\u2009\u00b0C. Equations are provided for calculating viscosity index for petroleum products having kinematic viscosities above 70\u2009mm2<\/sup>\/s at 100\u2009\u00b0C.<\/p>\n

\n

1.2.1<\/span> In cases where kinematic viscosity data are not available at temperatures of 40\u2009\u00b0C and 100\u2009\u00b0C, an estimate may be made of the viscosity index by calculating the kinematic viscosity at temperatures of 40\u2009\u00b0C and 100\u2009\u00b0C from data obtained at other temperatures. Such viscosity index data may be considered as suitable for information only and not for specification purposes. See Test Method D341<\/span>, Annex A1.<\/p>\n<\/p><\/div>\n<\/p><\/div>\n

\n

1.3<\/span> The kinematic viscosity values are determined with reference to a value of 1.0034\u2009mm2<\/sup>\/s at 20.00\u2009\u00b0C for distilled water. The determination of the kinematic viscosity of a petroleum product shall be carried out in accordance with Test Methods D445<\/span>, D7042<\/span>, IP 71, or ISO 3104.<\/p>\n

\n

1.3.1<\/span> If Viscosity Index calculated for a given sample using kinematic viscosity measurements from different test methods are in disagreement, the values calculated from Test Method D445<\/span> measurements shall be accepted.<\/p>\n<\/p><\/div>\n<\/p><\/div>\n

\n

1.4<\/span> The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.<\/p>\n

\n

1.4.1<\/span> The values stated in SI units are to be regarded as the standard. For user reference, 1\u2009mm2<\/sup>\/s = 10-6<\/sup>m 2<\/sup>\/s = 1 cSt.<\/p>\n<\/p><\/div>\n<\/p><\/div>\n

\n

1.5<\/span> This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.<\/i><\/p>\n<\/p><\/div>\n

\n

1.6<\/span> This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.<\/i><\/p>\n<\/p><\/div>\n

Keywords<\/strong><\/p>\n

kinematic viscosity; viscosity index;<\/p>\n

ICS Code<\/strong><\/p>\n

ICS Number Code 17.060 (Measurement of volume, mass, density, viscosity)<\/p>\n

DOI:<\/strong> 10.1520\/D2270-24<\/p>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

D2270-24 Standard Practice for Calculating Viscosity Index from Kinematic Viscosity at 40\u2009\u00b0C and 100\u2009\u00b0C (Redline)<\/b><\/p>\n\n\n\n\n
Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
ASTM<\/b><\/a><\/td>\n2024<\/td>\n8<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":461032,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[2637],"product_tag":[],"class_list":{"0":"post-461022","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-astm","8":"first","9":"instock","10":"sold-individually","11":"shipping-taxable","12":"purchasable","13":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/461022","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/461032"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=461022"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=461022"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=461022"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}