{"id":72797,"date":"2024-10-17T16:24:03","date_gmt":"2024-10-17T16:24:03","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/awwa-c200-2005\/"},"modified":"2024-10-24T19:08:09","modified_gmt":"2024-10-24T19:08:09","slug":"awwa-c200-2005","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/awwa\/awwa-c200-2005\/","title":{"rendered":"AWWA C200 2005"},"content":{"rendered":"
This standard covers electrically butt-welded, straight seam or spiral seam steel pipe, 6 in. (150 mm) and larger, for transmission and distribution of water, including fabrication of pipe, requirements of welding operations, permissible variations of weight and dimensions, preparation of ends, fabrication of specials, inspection, and test procedures.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
1<\/td>\n | AWWA C200-05 <\/td>\n<\/tr>\n | ||||||
3<\/td>\n | Committee Personnel <\/td>\n<\/tr>\n | ||||||
7<\/td>\n | Contents <\/td>\n<\/tr>\n | ||||||
9<\/td>\n | Foreword I. Introduction. <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | II. Special Issues. <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | III. Use of This Standard. <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | IV. Major Revisions. V. Comments. <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | AWWA Standard Steel Water Pipe-6 In. (150 mm) and Larger \n SECTION 1: GENERAL Sec. 1.1 Scope Sec. 1.2 Purpose Sec. 1.3 Application <\/td>\n<\/tr>\n | ||||||
18<\/td>\n | SECTION 2: REFERENCES <\/td>\n<\/tr>\n | ||||||
20<\/td>\n | SECTION 3: DEFINITIONS <\/td>\n<\/tr>\n | ||||||
23<\/td>\n | SECTION 4: REQUIREMENTS Sec. 4.1 Permeation <\/td>\n<\/tr>\n | ||||||
24<\/td>\n | Sec. 4.2 Materials and Workmanship Sec. 4.3 Drawings <\/td>\n<\/tr>\n | ||||||
25<\/td>\n | Sec. 4.4 Calculations Sec. 4.5 Protective Coating Sec. 4.6 Pipe Made to ASTM Requirements Sec. 4.7 Fabricated Pipe <\/td>\n<\/tr>\n | ||||||
26<\/td>\n | Table 1 Steel plate, sheet, or coils for fabricated pipe <\/td>\n<\/tr>\n | ||||||
27<\/td>\n | Sec. 4.8 Selection of Materials Sec. 4.9 General Requirements for Fabrication of Pipe Sec. 4.10 Fabrication of Pipe <\/td>\n<\/tr>\n | ||||||
28<\/td>\n | Sec. 4.11 Requirements for Welding Operations <\/td>\n<\/tr>\n | ||||||
31<\/td>\n | Table 2 Guided-bend test jig dimensions <\/td>\n<\/tr>\n | ||||||
33<\/td>\n | Sec. 4.12 Permissible Variations in Weights and Dimensions <\/td>\n<\/tr>\n | ||||||
34<\/td>\n | Sec. 4.13 Preparation of Ends <\/td>\n<\/tr>\n | ||||||
38<\/td>\n | Sec. 4.14 Special Ends Sec. 4.15 Specials and Fittings <\/td>\n<\/tr>\n | ||||||
39<\/td>\n | Sec. 4.16 Fabrication of Specials SECTION 5: VERIFICATION Sec. 5.1 Inspection <\/td>\n<\/tr>\n | ||||||
40<\/td>\n | Sec. 5.2 Test Procedures <\/td>\n<\/tr>\n | ||||||
42<\/td>\n | Sec. 5.3 Calibration of Equipment SECTION 6: DELIVERY Sec. 6.1 Marking <\/td>\n<\/tr>\n | ||||||
43<\/td>\n | Sec. 6.2 Handling and Loading Sec. 6.3 Affidavit of Compliance <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" AWWA C200-05: Steel Water Pipe 6 Inch (150 MM) & Larger<\/b><\/p>\n |