šŸ”„šŸ”„ Donā€™t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

šŸ”
BS EN 16062:2023

BS EN 16062:2023

$189.07

Intelligent transport systems. ESafety. eCall high level application requirements (HLAP) using GSM/UMTS circuit switched networks

Published By Publication Date Number of Pages
BSI 2023 48
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

In respect of pan-European eCall (operating requirements defined in EN 16072), this European Standard defines the high level application protocols, procedures and processes required to provide the eCall service using a TS12 emergency call over a mobile communications network. NOTE 1 The objective of implementing the pan-European in-vehicle emergency call system (eCall) is to automate the notification of a traffic accident, wherever in Europe, with the same technical standards and the same quality of services objectives by using a PLMN (such as ETSI prime medium) which supports the European harmonized 112/E112 emergency number (TS12 ETSI/TS 122 003) and to provide a means of manually triggering the notification of an emergency incident. NOTE 2 HLAP requirements for third party services supporting eCall can be found in EN 16102, and have been developed in conjunction with the development of this work item, and is consistent in respect of the interface to the PSAP. This deliverable makes reference to those provisions but does not duplicate them.

PDF Catalog

PDF Pages PDF Title
2 undefined
9 1 Scope
2 Normative references
10 3 Terms and definitions
13 4 Symbols and abbreviations
14 5 Conformance
16 6 General overview of the eCall transaction for Pan European eCall
20 7 Requirements
7.1 General requirements
7.1.1 General
7.1.2 USIM
7.1.3 Enabled PSAP
7.1.4 IVS configured only for eCall
21 7.1.5 Self-test
7.1.6 Standby mode applicable to IVS configured for eCall only
7.2 Activation
7.2.1 Activation of pan-European eCall
22 7.2.2 Activation of a test eCall
7.3 Call set-up
7.3.1 General
7.3.2 IVS network access device (NAD) already registered on PLMN
7.3.3 eCall in progress
7.3.4 Network selection and registration
23 7.3.5 Authentication of the subscriber
7.3.6 eCall establishment
7.3.7 Cell localization (by network)
24 7.3.8 Manual termination of eCall by vehicle occupants before trigger confirmation
7.4 MSD transfer
7.4.1 General
7.4.1.1 General
25 7.4.1.2 PSAP PULL mode
7.4.1.3 PSAP PUSH mode
7.4.2 Send initiation signal from IVS eCall modem to PSAP
7.4.3 eCall modem synchronization
26 7.4.4 Request MSD by PSAP eCall modem to IVS eCall modem
7.4.5 Send MSD from vehicle IVS to PSAP eCall modem
7.4.6 Link layer error check
7.4.7 Link layer ACK from PSAP eCall modem to IVS eCall modem
27 7.5 Application layer acknowledgement (AL- ACK)
7.5.1 Following transmission of the MSD to the eCall PSAP application
7.5.2 PSAP acknowledges the MSD
7.5.3 No receipt of application layer ACK
7.5.4 Form of presentation of the AL-ACK
29 7.6 PSAP request ā€œSEND MSDā€
7.6.1 General
7.6.2 Before call clear-down
31 7.6.3 After call clear-down
7.7 (void)
7.8 Audio link to vehicle occupants
7.9 eCall clear-down
32 7.10 PSAP call back
7.11 Rerouting to another PSAP/emergency control centre
33 7.12 Handling non equipped situations / error cases
7.12.1 MSD not transmitted correctly
7.12.2 Network registration fails
7.12.3 Call failure before the MSD is sent and acknowledged
7.12.4 Mobile network not supporting eCall flag or not provided with routing tables
7.12.4.1 General
34 7.12.4.2 Route both eCalls and 112/E112 voice calls to a PSAP that is equipped to support the eCall service
7.12.4.3 Route both eCalls and 112/E112 voice calls to a PSAP not equipped to support the eCall service
7.12.5 PSAP modem failure
7.12.5.1 Before link layer ACK is sent
7.12.5.2 After link layer ACK is sent
7.12.5.3 After application ACK is sent
7.12.6 PSAP network/ICT failure
7.12.7 PSAP application failure
7.12.8 PSAP operator does not respond
35 7.12.9 No response if line engaged
7.12.10 MSD not sent
7.12.11 MSD not received
7.12.12 Audio link not established
36 7.12.13 Audio link established but subsequently fails
7.12.14 Re-attempt in case of interrupted call
7.12.15 Automatic repeat attempts
7.12.16 IVS NAD does not receive call clear-down
8 Third party services supported eCall (TPS-eCall)
37 9 Defences against attack (Security provisions)
10 Quality of service requirements
11 Test and conformance requirements
12 Marking, labelling and packaging
13 Declaration of patents and intellectual property
38 Annex A (normative)Table of timings
41 Annex B (informative)(void)
42 Annex C (informative)Test system strategies
C.1 General
C.2 Vehicle and PSAP equipment life cycle
43 C.3 Laboratory environment
C.4 OEM or third party test systems

Related products

BS EN 16062:2023
$189.07