{"id":180247,"date":"2024-10-19T11:15:17","date_gmt":"2024-10-19T11:15:17","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/nfpa-270-2018\/"},"modified":"2024-10-25T03:32:46","modified_gmt":"2024-10-25T03:32:46","slug":"nfpa-270-2018","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/nfpa\/nfpa-270-2018\/","title":{"rendered":"NFPA 270 2018"},"content":{"rendered":"
This test method provides a means of measuring smoke obscuration of essentially flat materials, products, or assemblies (including surface finishes) up to 25mm thick, when exposed to specified levels of thermal irradiance in a single closed chamber.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
2<\/td>\n | Important Notices and Disclaimers <\/td>\n<\/tr>\n | ||||||
3<\/td>\n | Additional Notices and Disclaimers <\/td>\n<\/tr>\n | ||||||
7<\/td>\n | Chapter 1 Administration 1.1 Scope. 1.2 Purpose. (Reserved) 1.3 Application. <\/td>\n<\/tr>\n | ||||||
8<\/td>\n | 1.4 Units and Formulas. Chapter 2 Referenced Publications 2.1 General. 2.2 NFPA Publications. (Reserved) 2.3 Other Publications. <\/td>\n<\/tr>\n | ||||||
9<\/td>\n | 2.4 References for Extracts in Mandatory Sections. (Reserved) Chapter 3 Definitions 3.1 General. 3.2 NFPA Official Definitions. 3.3 General Definitions. Chapter 4 Test Apparatus 4.1 General. 4.2 Test Chamber. <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | 4.3 Sample Support and Heating Arrangements. <\/td>\n<\/tr>\n | ||||||
12<\/td>\n | 4.4 Gas Supply. <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | 4.5 Photometric System. <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | 4.6 Chamber Leakage. 4.7 Cleaning Materials. 4.8 Ancillary Equipment. Chapter 5 Test Environment 5.1 Light Interference. 5.2 Product of Combustion Venting. 5.3 Operator Safety. <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | Chapter 6 Test Specimen 6.1 Suitability of Sample for Testing. 6.2 Sample Face. 6.3 Number of Specimens. 6.4 Additional Specimens. 6.5 Size of Specimens. 6.6 Specimen Preparation. 6.7 Wrapping of Specimens. Chapter 7 Setup, Calibration, and Maintenance 7.1 Setup and Calibration Procedures. <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | 7.2 Alignment of Photometric System. 7.3 Selection of Compensating Filter(s). 7.4 Linearity Check. 7.5 Calibration of Range-Extension Filter. 7.6 Chamber Leakage Rate Test. <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | 7.7 Burner Calibration. 7.8 Radiator Cone Calibration. 7.9 Cleaning. 7.10 Frequency of Checking and Calibrating Procedures. 7.11 Total System. <\/td>\n<\/tr>\n | ||||||
18<\/td>\n | Chapter 8 Conditioning 8.1 Pre-Test. 8.2 Conditioning. Chapter 9 Test Procedure 9.1 Initial Conditions. 9.2 Tests with Pilot Flame. <\/td>\n<\/tr>\n | ||||||
19<\/td>\n | 9.3 Preparation of Photometric System. 9.4 Loading Specimen. 9.5 Recording of Light Transmission. 9.6 Observations. 9.7 Termination of Test. 9.8 Specimen Mass. 9.9 Repeat Tests. <\/td>\n<\/tr>\n | ||||||
20<\/td>\n | Chapter 10 Calculations 10.1 Specific Optical Density, Ds. 10.2 Clear Beam Correction Factor, Dc. 10.3 Mass Loss. Chapter 11 Test Report 11.1 Descriptive Information. 11.2 Test Results. <\/td>\n<\/tr>\n | ||||||
21<\/td>\n | Annex A Explanatory Material <\/td>\n<\/tr>\n | ||||||
23<\/td>\n | Annex B Precision and Bias <\/td>\n<\/tr>\n | ||||||
26<\/td>\n | Annex C Interlaboratory Application <\/td>\n<\/tr>\n | ||||||
27<\/td>\n | Annex D Determination of Mass Optical Density <\/td>\n<\/tr>\n | ||||||
32<\/td>\n | Annex E Informational References <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" NFPA 270: Standard Test Method for Measurement of Smoke Obscuration Using a Conical Radiant Source in a Single Closed Chamber<\/b><\/p>\n |