| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 2<\/td>\n | undefined <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | Foreword <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | Introduction <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 1 Scope 2 Normative references 3 Terms, definitions, symbols and units 3.1 Terms and definitions <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 3.2 Symbols and units of measurement <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 4 Selection of heating appliances to be tested 4.1 Classification <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 4.2 Selection of models to be tested for determining the thermal outputs of a type 4.2.1 Selection of models to be tested when the variable characteristic dimension is the overall height and the cross-section of the variable part is constant <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 4.2.2 Selection of models to be tested when the variable characteristic dimension for the type is other than the overall height <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 4.3 Testing samples submission and identification <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | 4.4 Supplementary test 5 Laboratory equipment and test methods 5.1 Principle 5.2 Apparatus 5.2.1 Test system 5.2.2 Reference test installation <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | 5.2.3 Master radiators <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | 5.2.4 Verification of test installation repeatability and reproducibility <\/td>\n<\/tr>\n | ||||||
| 31<\/td>\n | 5.2.5 Accuracy of measuring instruments and devices <\/td>\n<\/tr>\n | ||||||
| 32<\/td>\n | 5.2.6 Calibration of measuring instruments 5.3 Preparation for thermal output test 5.4 Test methods 5.4.1 General 5.4.2 Weighing method <\/td>\n<\/tr>\n | ||||||
| 33<\/td>\n | 5.4.3 Electric method 5.4.4 Measurements and calculations <\/td>\n<\/tr>\n | ||||||
| 36<\/td>\n | 5.4.5 Determination of the characteristic equation <\/td>\n<\/tr>\n | ||||||
| 37<\/td>\n | 5.5 Presentation of results 5.5.1 Standard thermal output of a model <\/td>\n<\/tr>\n | ||||||
| 38<\/td>\n | 5.5.2 Determination of the catalogue outputs of a type made at variable water flow rate 6 Test report <\/td>\n<\/tr>\n | ||||||
| 41<\/td>\n | Annex A (normative) Master radiators dimensional verification <\/td>\n<\/tr>\n | ||||||
| 46<\/td>\n | Annex B (informative) Determination of pressure drop <\/td>\n<\/tr>\n | ||||||
| 51<\/td>\n | Annex C (normative) Least squares regression for a model <\/td>\n<\/tr>\n | ||||||
| 52<\/td>\n | Annex D (normative) Analysis of test results by the method of least squares multiple regression <\/td>\n<\/tr>\n | ||||||
| 54<\/td>\n | Annex E (normative) Specimen of the test report <\/td>\n<\/tr>\n | ||||||
| 57<\/td>\n | Annex F (informative) Apparatus and method for checking the bulk temperature measuring devices <\/td>\n<\/tr>\n | ||||||
| 59<\/td>\n | Annex G (informative) Examples of typical appliances according to Table 4 <\/td>\n<\/tr>\n | ||||||
| 69<\/td>\n | Annex H (normative) Determination of the \u03a6M values of the master radiators primary set <\/td>\n<\/tr>\n | ||||||
| 70<\/td>\n | Annex I (normative) Calculation method for determining the energy calculation parameters <\/td>\n<\/tr>\n | ||||||
| 72<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Radiators and convectors. Methods and rating for determining the heat output<\/b><\/p>\n |