{"id":486351,"date":"2024-11-05T12:13:27","date_gmt":"2024-11-05T12:13:27","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/agma-915-3-a99\/"},"modified":"2024-11-05T12:13:27","modified_gmt":"2024-11-05T12:13:27","slug":"agma-915-3-a99","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/agma\/agma-915-3-a99\/","title":{"rendered":"AGMA 915-3-A99"},"content":{"rendered":"<p>\n<u><strong>SCOPE<\/strong><\/u><\/p>\n<p>\tThis information sheet provides recommended values for dimensional deviations on blanks, center distance and parallelism of axes of gears.<\/p>\n<p>\tNumerical values given in this document are not to be regarded as strict ISO and AGMA quality criteria, but may serve as a guide for mutual agreements, for ferrous components.<\/p>\n<p>\n<u><strong>FOREWORD<\/strong><\/u><\/p>\n<p>\t[The foreword, footnotes and annexes, if any, in this document are provided for informational purposes only and are not to be construed as a part of AGMA 915-3-A99, <em>Inspection Practices \u2013 Gear Blanks, Shaft Center Distance and Parallelism<\/em>.]<\/p>\n<p>\tIn the course of revising ANSI\/AGMA 2000-A88, <em>Gear Classification and Inspection Handbook &#8211; Tolerances and Measuring Methods for Unassembled Spur and Helical Gears<\/em>, the AGMA Inspection Handbook Committee agreed that the ISO information from ISO\/TR 10064-3:1996, relative to the inspection of gear blanks, shaft center distance and parallelism of axes should be published under separate cover as an AGMA Information Sheet.<\/p>\n<p>\tFor the general replacement of ANSI\/AGMA 2000-A88, a system of documents as listed below, together with this information sheet, has been established:<\/p>\n<ul>\n<li>\n<p>\t\tAGMA 915-1-AXX, <em>Inspection Practices for Cylindrical Gears &#8211; Tangential Measurements<\/em><\/li>\n<li>\n<p>\t\tAGMA 915-2-AXX, <em>Inspection Practices for Cylindrical Gears &#8211; Radial Measurements<\/em><\/li>\n<li>\n<p>\t\tAGMA 915-4-AXX, <em>Inspection Practices &#8211; Recommendations Relative to Surface Texture<\/em><\/li>\n<li>\n<p>\t\tAGMA 2015-1-AXX, <em>Accuracy Classification System for Cylindrical Gears &#8211; Tangential Measurements<\/em><\/li>\n<li>\n<p>\t\tAGMA 2015-2-AXX, <em>Accuracy Classification System for Cylindrical Gears &#8211; Radial Measurements<\/em><\/li>\n<\/ul>\n<p>\tISO\/TR 10064-3:1996 was prepared by ISO Technical Committee TC 60, Gears.<\/p>\n<p>\tAGMA 915-3-A99 is not identical to ISO\/TR 10064-3:1996, <em>Cylindrical gears &#8211; Code of inspection practice &#8211; Part 3:\u00a0 Recommendations relative to gear blanks, shaft centre distance and parallelism of axe<\/em>s.\u00a0 It was agreed to be sent directly to committee comment in May of 1998, after project approval by the TDEC.\u00a0 The Committee, during comment resolution, made the following changes to the original ISO Technical Report:<\/p>\n<ul>\n<li>\n<p>\t\tAddition of reference to ISO 1101 in clause 4;<\/li>\n<li>\n<p>\t\tChanged the wording of the first paragraph of 4.3;<\/li>\n<li>\n<p>\t\tRevised figure 4, reversing the datum and runout callouts;<\/li>\n<li>\n<p>\t\tChanged 4.11 and figure 5, replacing datum surfaces with reference bands.<\/li>\n<\/ul>\n<p>\tThe Committee decided that these changes were sufficient enough to require an additional committee comment in February, 1999.<\/p>\n<p>\tIt was approved by the AGMA Technical Division Executive Committee on May 20, 1999.<\/p>\n","protected":false},"excerpt":{"rendered":"<p><b>Inspection Practices &#8211; Gear Blanks, Shaft Center Distance and Parallelism<\/b><\/p>\n<table style=\"width: 100%\" border=\"0\" cellspacing=\"0\" cellpadding=\"0\">\n<tbody>\n<tr>\n<td>Published By<\/td>\n<td>Publication Date<\/td>\n<td>Number of Pages<\/td>\n<\/tr>\n<tr>\n<td><a href=\"https:\/\/pdfstandards.shop\/product-category\/publishers\/agma\/\"><b>AGMA<\/b><\/a><\/td>\n<td>1999<\/td>\n<td>14<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":486361,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[2659],"product_tag":[],"class_list":{"0":"post-486351","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-agma","8":"first","9":"instock","10":"sold-individually","11":"shipping-taxable","12":"purchasable","13":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/486351","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/486361"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=486351"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=486351"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=486351"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}